mirror of
https://github.com/digistump/DigistumpArduino.git
synced 2025-04-28 07:39:02 -07:00
85 lines
2.6 KiB
Arduino
85 lines
2.6 KiB
Arduino
|
#include <IRLib.h> // In {path_of_installation}/Digispark-Arduino-1.0.x/libraries/DigisparkIRLib/IRLib.h, set MY_PROTOCOL to NEC, SONY, RC5 to find the one used by your own IR Remote Control
|
||
|
|
#include <DigiUSB.h> // In {path_of_installation}/Digispark-Arduino-1.0.x/libraries/DigisparkUSB/DigiUSB.h, RING_BUFFER_SIZE shall be set to 32
|
||
|
|
/*
|
||
|
|
_____ ____ __ _ ____ _ _ _ _
|
||
|
|
| __ \ / __ \ | \ | | / __ \ | | | | | | | |
|
||
|
|
| |__| | | / \_| | . \ | | / / \ \ | | | | \ \ / /
|
||
|
|
| _ / | | _ | |\ \| | | |__| | | | | | \ ' /
|
||
|
|
| | \ \ | \__/ | | | \ ' | | __ | \ \/ / | |
|
||
|
|
|_| \_\ \____/ |_| \__| |_| |_| \__/ |_| 2013
|
||
|
|
|
||
|
|
http://p.loussouarn.free.fr
|
||
|
|
|
||
|
|
*************************************************
|
||
|
|
* Optimized <IRLib> library Dump Demo *
|
||
|
|
*************************************************
|
||
|
|
|
||
|
|
This sketch allows you to discover the protocol used by your own IR Remote Control and the code of each key when pressed.
|
||
|
|
You will see the decoded key codes in the DigiUSB console.
|
||
|
|
|
||
|
|
IMPORTANT:
|
||
|
|
=========
|
||
|
|
- In {path_of_installation}/Digispark-Arduino-1.0.x/libraries/DigisparkIRLib/IRLib.h, set MY_PROTOCOL to NEC, SONY, RC5 to find the protocol used by your own IR Remote Control
|
||
|
|
- In {path_of_installation}/Digispark-Arduino-1.0.x/libraries/DigisparkUSB/DigiUSB.h, RING_BUFFER_SIZE shall be set to 32
|
||
|
|
|
||
|
|
Sensor wiring: (Warning: the wiring may vary depending of the model of IR sensor)
|
||
|
|
=============
|
||
|
|
.-------.
|
||
|
|
| ___ |
|
||
|
|
| / \ | InfraRed
|
||
|
|
| \___/ | Sensor
|
||
|
|
| |
|
||
|
|
'+--+--+'
|
||
|
|
| | | 100
|
||
|
|
P5 <----' | '--+---###--- +5V
|
||
|
|
| |
|
||
|
|
| '==='4.7uF
|
||
|
|
| |
|
||
|
|
'--+--'
|
||
|
|
|
|
||
|
|
GND
|
||
|
|
|
||
|
|
*/
|
||
|
|
|
||
|
|
#define LED_PIN 1
|
||
|
|
#define IR_RX_PIN 5
|
||
|
|
|
||
|
|
#define BUTTON_OFF 0xF740BF //Set here the OFF code for the built-in LED when determined
|
||
|
|
#define BUTTON_ON 0xF7C03F //Set here the ON code for the built-in LED when determined
|
||
|
|
|
||
|
|
IRrecv My_Receiver(IR_RX_PIN);//Receive on pin IR_RX_PIN
|
||
|
|
IRdecode My_Decoder;
|
||
|
|
|
||
|
|
void setup()
|
||
|
|
{
|
||
|
|
My_Receiver.enableIRIn(); // Start the receiver
|
||
|
|
pinMode(LED_PIN, OUTPUT);
|
||
|
|
DigiUSB.begin();
|
||
|
|
}
|
||
|
|
|
||
|
|
void loop()
|
||
|
|
{
|
||
|
|
if(My_Receiver.GetResults(&My_Decoder))
|
||
|
|
{
|
||
|
|
My_Decoder.decode();
|
||
|
|
switch(My_Decoder.value)
|
||
|
|
{
|
||
|
|
case BUTTON_OFF:
|
||
|
|
digitalWrite(LED_PIN, LOW);
|
||
|
|
break;
|
||
|
|
case BUTTON_ON:
|
||
|
|
digitalWrite(LED_PIN, HIGH);
|
||
|
|
break;
|
||
|
|
default:break;
|
||
|
|
}
|
||
|
|
My_Receiver.resume();
|
||
|
|
DigiUSB.println(My_Decoder.value, HEX);
|
||
|
|
}
|
||
|
|
if(DigiUSB.available())
|
||
|
|
{
|
||
|
|
DigiUSB.read();
|
||
|
|
}
|
||
|
|
DigiUSB.refresh();
|
||
|
|
}
|
||
|
|
|