switch to setup for Arduino Boards Manager

digistump-sam/libraries/Wire/examples/SFRRanger_reader/SFRRanger_reader.pde

@@ -0,0 +1,87 @@
+// I2C SRF10 or SRF08 Devantech Ultrasonic Ranger Finder 
+// by Nicholas Zambetti <http://www.zambetti.com>
+// and James Tichenor <http://www.jamestichenor.net> 
+
+// Demonstrates use of the Wire library reading data from the 
+// Devantech Utrasonic Rangers SFR08 and SFR10
+
+// Created 29 April 2006
+
+// This example code is in the public domain.
+
+
+#include <Wire.h>
+
+void setup()
+{
+  Wire.begin();                // join i2c bus (address optional for master)
+  Serial.begin(9600);          // start serial communication at 9600bps
+}
+
+int reading = 0;
+
+void loop()
+{
+  // step 1: instruct sensor to read echoes
+  Wire.beginTransmission(112); // transmit to device #112 (0x70)
+                               // the address specified in the datasheet is 224 (0xE0)
+                               // but i2c adressing uses the high 7 bits so it's 112
+  Wire.write(byte(0x00));      // sets register pointer to the command register (0x00)  
+  Wire.write(byte(0x50));      // command sensor to measure in "inches" (0x50) 
+                               // use 0x51 for centimeters
+                               // use 0x52 for ping microseconds
+  Wire.endTransmission();      // stop transmitting
+
+  // step 2: wait for readings to happen
+  delay(70);                   // datasheet suggests at least 65 milliseconds
+
+  // step 3: instruct sensor to return a particular echo reading
+  Wire.beginTransmission(112); // transmit to device #112
+  Wire.write(byte(0x02));      // sets register pointer to echo #1 register (0x02)
+  Wire.endTransmission();      // stop transmitting
+
+  // step 4: request reading from sensor
+  Wire.requestFrom(112, 2);    // request 2 bytes from slave device #112
+
+  // step 5: receive reading from sensor
+  if(2 <= Wire.available())    // if two bytes were received
+  {
+    reading = Wire.read();  // receive high byte (overwrites previous reading)
+    reading = reading << 8;    // shift high byte to be high 8 bits
+    reading |= Wire.read(); // receive low byte as lower 8 bits
+    Serial.println(reading);   // print the reading
+  }
+
+  delay(250);                  // wait a bit since people have to read the output :)
+}
+
+
+/*
+
+// The following code changes the address of a Devantech Ultrasonic Range Finder (SRF10 or SRF08)
+// usage: changeAddress(0x70, 0xE6);
+
+void changeAddress(byte oldAddress, byte newAddress)
+{
+  Wire.beginTransmission(oldAddress);
+  Wire.write(byte(0x00));
+  Wire.write(byte(0xA0));
+  Wire.endTransmission();
+
+  Wire.beginTransmission(oldAddress);
+  Wire.write(byte(0x00));
+  Wire.write(byte(0xAA));
+  Wire.endTransmission();
+
+  Wire.beginTransmission(oldAddress);
+  Wire.write(byte(0x00));
+  Wire.write(byte(0xA5));
+  Wire.endTransmission();
+
+  Wire.beginTransmission(oldAddress);
+  Wire.write(byte(0x00));
+  Wire.write(newAddress);
+  Wire.endTransmission();
+}
+
+*/