mirror of
https://github.com/digistump/DigistumpArduino.git
synced 2025-04-28 15:49:02 -07:00
79 lines
3.1 KiB
Plaintext
79 lines
3.1 KiB
Plaintext
/* ATtiny85 as an I2C Master Ex1 BroHogan 1/21/11
|
|
* I2C master reading DS1621 temperature sensor. (display with leds)
|
|
* SETUP:
|
|
* ATtiny Pin 1 = (RESET) N/U ATtiny Pin 2 = (D3) LED3
|
|
* ATtiny Pin 3 = (D4) to LED1 ATtiny Pin 4 = GND
|
|
* ATtiny Pin 5 = SDA on DS1621 ATtiny Pin 6 = (D1) to LED2
|
|
* ATtiny Pin 7 = SCK on DS1621 ATtiny Pin 8 = VCC (2.7-5.5V)
|
|
* NOTE! - It's very important to use pullups on the SDA & SCL lines!
|
|
* DS1621 wired per data sheet. This ex assumes A0-A2 are set LOW for an addeess of 0x48
|
|
* TinyWireM USAGE & CREDITS: - see TinyWireM.h
|
|
* NOTES:
|
|
* The ATtiny85 + DS1621 draws 1.7mA @5V when leds are not on and not reading temp.
|
|
* Using sleep mode, they draw .2 @5V @ idle - see http://brownsofa.org/blog/archives/261
|
|
*/
|
|
|
|
#include <TinyWireM.h> // I2C Master lib for ATTinys which use USI
|
|
|
|
#define DS1621_ADDR 0x48 // 7 bit I2C address for DS1621 temperature sensor
|
|
#define LED1_PIN 4 // ATtiny Pin 3
|
|
#define LED2_PIN 1 // ATtiny Pin 6
|
|
#define LED3_PIN 3 // ATtiny Pin 2
|
|
|
|
int tempC = 0; // holds temp in C
|
|
int tempF = 0; // holds temp in F
|
|
|
|
|
|
void setup(){
|
|
pinMode(LED1_PIN,OUTPUT);
|
|
pinMode(LED2_PIN,OUTPUT);
|
|
pinMode(LED3_PIN,OUTPUT);
|
|
Blink(LED1_PIN,2); // show it's alive
|
|
TinyWireM.begin(); // initialize I2C lib
|
|
Init_Temp(); // Setup DS1621
|
|
delay (3000);
|
|
}
|
|
|
|
|
|
void loop(){
|
|
Get_Temp();
|
|
Blink(LED1_PIN,tempC/10); // blink 10's of temperature on LED 1
|
|
delay (1000);
|
|
Blink(LED2_PIN,tempC%10); // blink 1's of temperature on LED 2
|
|
delay (4000); // wait a few sec before next reading
|
|
}
|
|
|
|
|
|
void Init_Temp(){ // Setup the DS1621 for one-shot mode
|
|
TinyWireM.beginTransmission(DS1621_ADDR);
|
|
TinyWireM.send(0xAC); // Access Command Register
|
|
TinyWireM.send(B00000001); // Using one-shot mode for battery savings
|
|
//TinyWireM.send(B00000000); // if setting continious mode for fast reads
|
|
TinyWireM.endTransmission(); // Send to the slave
|
|
}
|
|
|
|
|
|
void Get_Temp(){ // Get the temperature from a DS1621
|
|
TinyWireM.beginTransmission(DS1621_ADDR);
|
|
TinyWireM.send(0xEE); // if one-shot, start conversions now
|
|
TinyWireM.endTransmission(); // Send 1 byte to the slave
|
|
delay(750); // if one-shot, must wait ~750 ms for conversion
|
|
TinyWireM.beginTransmission(DS1621_ADDR);
|
|
TinyWireM.send(0xAA); // read temperature (for either mode)
|
|
TinyWireM.endTransmission(); // Send 1 byte to the slave
|
|
TinyWireM.requestFrom(DS1621_ADDR,1); // Request 1 byte from slave
|
|
tempC = TinyWireM.receive(); // get the temperature
|
|
tempF = tempC * 9 / 5 + 32; // convert to Fahrenheit
|
|
}
|
|
|
|
|
|
void Blink(byte led, byte times){ // poor man's GUI
|
|
for (byte i=0; i< times; i++){
|
|
digitalWrite(led,HIGH);
|
|
delay (400);
|
|
digitalWrite(led,LOW);
|
|
delay (175);
|
|
}
|
|
}
|
|
|